Friday, May 17, 2013
How To Build A Soda cans Stove
If all you want to do is boil water, consider making a cat food can stoveinstead of a soda can stove. It would be easier to make than a soda can stove-plus it's lighter and pot support acts as a built-in! But if you need to do more than boil water, you are in the right place!
Materials List
Most materials you need may already be putting on your place.One thing you may not have is a tape that will not burn when you use your stove! You can find the record high temperature in any decent hardware store.It is designed for use on flues or muffler or something-I do not really know. But it is made of materials that will not burn or melt. A roll should cost under $ 10, but you might be able to make a hundred stoves from a single roll. You do not need much!
- soda cans - a minimum of two is required, but a few extra for mistakes, simmer ring, and the like can be useful. Get a six-pack and throw a party! =)
- a ruler or tape measure
- scratch awl or sharp instrument
- heavy duty x-acto knife (or something similar)
- Sharpie
- scissors
- high temperature tape
(Aka Metal tape, aluminum tape, foil tape, tape the exhaust, or basically any type of tape that will not burn)
Some people claim that Pepsi is the soda cans can be a superior choice. I have used a can of Coke, root beer, soda and wine and never even notice the difference, so drink what you like. It does not really make a difference!
Step 1: Create Hole Burner
Poke holes along the bottom edge of one of the cans with initial awl. Some people say a small hole that is more fuel efficient. Some people like a big hole because it burns faster and hotter. I like the 'normal' hole. Number of holes does not really matter-just as long as they go around the circle more-or-less evenly. I usually poke two holes on opposite sides, then two more holes halfway between the original hole. Then four more holes between the first four. And then eight holes between the first eight for a total of 16 holes.
Step 2: Create Opening Main
Cut the bottom you can only go poking holes in the tin is pretty thick here, so it should be a solid instrument to do this. An X-acto knife will work, but using one with a heavy duty knife on it. I use the knife from cutting kit Speedball linoleum. Use whatever you have. If the edges are very jagged turns, you can file them down now. (Or later, or not at all-is not important to me!)
Step 3: Cut Out Top Stove
Measuring up to 20mm (3/4 in) from the bottom of the can and cut. This will be the top of your stove. To get even cut, I marked the point at 20mm, then hold steady Sharpie on the table as he turned around to menentangnya.Sebuah clean, even the mark completely in the can every time! It's easier to get a clean cut if you first do the rough cuts to get the final can be separated, then cut along marks the second straight where necessary.
Step 4: Cut Tabs on Top Stove
Snip the edge of the stove top a few times to form a tab. We will fit the stove top to the bottom of the stove and the little tab to help make sure it fits! I make eight evenly spaced snips around the stove, to the point where just below the paint in cans stop.
Step 5: Cut Out Down Stoves
Now it's time to take a new can and cut the bottom of it. Do not poke a hole in it or cut the bottom as you do to the top of the stove. This time, the size of 25mm (1 in) from the bottom of the can and dipotong.Jika you want to get wild and crazy, you can make your stove as tall or short as you like by adjusting these measurements be 10mm shorter than the height you want for the end of the stove . For your first stove, stick with the standard 25mm.Measure, mark and cut.
Step 6: Cut out the inner walls
And now, the inner wall. Take a left on the remains of one of the two cans before you cut. If you do not mangle them too bad, you can cut the inner wall of one of them. If not, you have to operate on all three cans. You have to cut a strip of 35mm (1 1/3 in). (If you are going crazy and make your stove is shorter or taller, measuring to the desired height of your stove In this case, we will be 35mm high stove ..)
Step 7: In the Wall Dimensions
Size of the inner wall of the bottom of the cooker. You will be cut in half through the strip at each end on opposite sides of the strip where the ends will lock together. When you lock the edges, make sure the ends of the strips are in the loop. This self-locking and more stable that way. I've put a red X with a photo showing the incorrect way to lock the end of the inner wall.
Step 8: Trim Wall In
Trim the inner wall. You can cut a tiny bit off the end of the strip off to savea small smidgen of weight, but it is very important to cut three small notches about the same distance around one side of the strip. This allows fuel to flow through the inner wall to the outer wall.
Step 9: Assemble Parts
It's time to put the three pieces. Begin by placing the bottom of the inner walls of the stove, with a notched end down. Then in accordance with the stove on, tucking 'tab' you cut earlier in the bottom of the stove. Some hints to get on-top that it's not as easy as you might think! Sharp edges of the 'tab' tend to get caught when putting on the top, so it curves slightly to the tab before you start. You can see I've done this in the second photo below where he gives the top looks ruffled. The last bit of the above is the most difficult to squeeze in, so use a knife or other thin items such shoehorn to get it pushed in. Check the inner wall fits into the woods off the stove correctly. Working on it slowly and evenly, and eventually everything will fit together like a puzzle.
Step 10: Taping It All Together
Stove should stay in one piece for not more than the friction of the pieces, but it's not too safe like this. Use high temperature tape to keep the stove together permanently. Depending on the width of the ribbon, you may have to cut it in half like I did. Then wrap it around the stove, securing the top and bottom of the stove together.
Step 11: Create Ring Simmer (optional)
This optional simmer ring is very useful if you want to bake yourself a treat or if the recipe calls for food to simmer. It is made from the top of soda cans. Remove the tab, and then cut it out just where the can down the long curve of the tin. Leave a little too much, then trim a bit smaller than at a time until it fits snugly on top of your stove.
Step 12: Make a Snuffer (optional)
Snuffer's, when placed on the stove, will help you extinguish it. In general, I recommend just letting any residual alcohol just burn. Once, while trying to save fuel, I tried to put the fire out, tapped into my lap instead stove, and lit my crotch on fire. Indeed, let the alcohol burn! But if you really need to save fuel, using an optional Snuffer. This will starve the stove of oxygen and extinguish the fire. Usually less oxygen still gets in so you have to press the lid (not with fingers!) Or pour water on it to get the fire completely out, but it will work.
Caveats aside, making Snuffer like you do with a simmer ring, but the bottom of the can instead of using it. Cut too high, then trim off thin slices until it fits snugly on top of the stove.
That's it! You're done!
At least, you're done with cans of soda stove itself. Now you can build a support pan for your stove, find some denatured alcohol , and figuring outhow to use your soda can stove. Enjoy!
Subscribe to:
Posts (Atom)